{"product_id":"billet-connecting-rod-arc-racing-honda-gx160-gx200-clone-3-595-x-1-183-x-490","title":"Billet Connecting Rod, ARC Racing Honda GX160,GX200,Clone 3.595\" x 1.183\" x .490\"","description":"\u003c!--StartFragment--\u003e\u003cp\u003eThe New ARC \"Drop In\" long rod for the \u003cstrong\u003eHonda GX200 and Clone 196cc\u003c\/strong\u003e engines does not require cutting down the top of the 11132P 2 ring Wiseco piston, or can be used with the new 3 ring Wiseco pistons. This rod measures 3.595\" center to center for a \u003cstrong\u003e1.180\"\u003c\/strong\u003e crank pin with \u003cstrong\u003e.490\"\u003c\/strong\u003e wrist pin and is designed to be used with aftermarket high-performance pistons.*\u003cstrong\u003e Bearings and custom designed high tensile strength ARP bolts are included\u003c\/strong\u003e. All of our rods are CNC machined from aircraft grade domestic 7075 T-651 aluminum. Our OHV rods are designed to utilize the higher compression ratios and high RPMs of racing OHV engines. Key Features Include: Oil groove in the crank bore that is fed through a channel in the integrated forced oil dipper arm. Oil groove in the wrist pin bore that provides a reservoir of lubricant to the wrist pin as well as reinforced wrist pin bosses on the rod . \u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eRod bolt torque: 170 Inch\/lbs lubricated\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e***Will Not fit the Hemi or Non Hemi Predator cranks***\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e Installation Instructions:\u003c\/p\u003e\u003cp\u003eTo install your ARC rod you will need a \u003cstrong\u003e12 point 1\/4\" socket\u003c\/strong\u003e and a\u003cstrong\u003e QUALITY inch pound torque wrench\u003c\/strong\u003e. You will need an outside micrometer, dial bore gauge or plasti gauge, and motor oil.\u003c\/p\u003e\u003cp\u003eMeasure the crank pin diameter with the outside mic, it should measure \u003cstrong\u003e1.180-1.1795\"\u003c\/strong\u003e. Measure in several spots to insure roundness. If larger than 1.180\", crank journal should be polished down to spec. If journal is out of round more than .0005\" it probably should be replaced. The crank pin finish should be smooth to the touch.\u003c\/p\u003e\u003cp\u003eWhen disassembling the rod notice on the side of the rod with the part number there are two dots next to the separation point of the beam and cap (some older rods don't have these). These dots help to re-orientate the cap and beam when assembled. The side of the rod with the part number engraved will always face the side cover, and all oiling holes in the rod will face the cam. \u003c\/p\u003e\u003cp\u003eMake sure the bearing and rod serrations are clean. Install the bearings by lining up the tangs on the bearing with the cut outs on the rod. Lubricate the rod bolt threads with straight motor oil and hand tighten the bolts. Using the torque wrench and\u003cstrong\u003e 12 point 1\/4\" socket\u003c\/strong\u003e tighten the bolts to 60\" Inch\/lbs. Alternate each side to increase the torque by 20\" lbs at a time until you reach 150\" Inch\/lbs. This helps seat the rod bearing especially on a new rod. Measure the bore with your dial bore gauge opposite the parting lines. If using plasti gauge you will have to install the rod on the crank and use in accordance the plasti gauge instructions.\u003c\/p\u003e\u003cp\u003eThe rod bore should measure 1.183 +\/.0005\". With plasti gauge you are looking for about\u003cstrong\u003e .003\" total oil clearance\u003c\/strong\u003e. From .0025-.0035\" clearance is acceptable. Anything outside that dimension please call 800-521-3560 for recommendation.\u003c\/p\u003e\u003cp\u003eOnce clearance is set apply motor oil to rod bolts, bearings, crank journal, and wrist pin. Then install.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo Not use sticky automotive assembly lube, always use the oil you plan to run in the engine as assembly lube for all internal parts.\u003c\/strong\u003e  \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFinal rod bolt torque is 170\"Inch\/lbs.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eImproperly torqueing rod bolts is one of the most common causes of rod failure.\u003c\/p\u003e\u003c!--EndFragment--\u003e\n\n\u003cbr\u003e","brand":"ARC Racing","offers":[{"title":"Default","offer_id":43476895465627,"sku":"ARC-1057","price":89.95,"currency_code":"USD","in_stock":true}],"url":"https:\/\/www.badassminis.com\/de\/products\/billet-connecting-rod-arc-racing-honda-gx160-gx200-clone-3-595-x-1-183-x-490","provider":"Bad Ass Minis","version":"1.0","type":"link"}